Robot vacuum listings lead with a suction number, and the numbers climb every year: a few thousand pascals, then several thousand, then more. It looks like a measurement of cleaning power, the way horsepower measures an engine. It is not. A shopper who picks the highest number may end up with a machine that leaves crumbs along the edges, tangles on a rug fringe or loses its way under the sofa.
This guide explains what the figure measures, why it cannot be compared between brands, and what actually determines cleaning on a real floor: brush roll design, airflow, sealing, bin size, navigation, the floor type, mop add-ons, docks and the maintenance that keeps any of it working. It aims to help you read a spec sheet and spot the details that matter.
What a Pa figure measures
The pascal is a unit of pressure. Suction in a vacuum is the pressure difference between the inside of the machine and the outside air. A higher figure means the machine can create a stronger vacuum when the inlet is sealed, and that is typically how it is measured, with the nozzle blocked and a gauge reading the pressure drop. It is a measure of the motor's ability to create a pressure difference, not of how it behaves when cleaning.
When the nozzle is open and air flows, the pressure drops and airflow rises, and cleaning ability depends on both together. A machine with high pressure and low airflow can hold a card to a wall but not lift sand from a carpet pile, because lifting debris needs a stream of moving air. Vacuum makers describe this as water lift against airflow, and the useful figure is a combination that robot makers rarely publish.
Because the test conditions vary, two machines with the same Pa figure may clean differently. No source documents one test that every brand follows, so a box number reflects the maker's own method, motor setting and sometimes the maximum boost mode that cannot be sustained. The honest approach is to treat the figure as a rough tier within a brand, not as a comparison between brands.
Brush roll design matters more than the number
On carpet, most dirt is pulled out by agitation, not by suction alone. A rotating brush beats and combs the fibres, loosening embedded dust so the airflow can carry it away. A machine with a modest suction figure and an excellent brush can outclean a stronger one with a poor brush, and on hard floors the brush's job is to sweep debris toward the inlet.
Brush types differ. Bristle brushes are effective on carpet but tangle with hair, which wraps around the roll and slows it. Rubber or silicone brushes, with flexible fins, resist tangling and work well on hard floors and short pile, at the cost of less agitation deep in carpet. Some machines combine the two, with rubber blades and bristle strips, which is a reasonable compromise.
Look for how hair is handled. Some machines have a comb or a cutter that clears hair from the roll, and some use a brushless design that relies on airflow. Check how easily the brush comes out for cleaning, because a brush you cannot remove in a few seconds will go uncleaned. Side brushes matter too, because they sweep edges and corners, where much of the dirt in a room collects.
| Feature | What it affects | What to look for |
|---|---|---|
| Suction (Pa) | Pressure the motor can create | Compare only within one brand |
| Brush roll | Agitation on carpet, tangling with hair | Tangle resistance, easy removal |
| Bin size | How often you empty it | Capacity in millilitres, ease of emptying |
| Navigation | Coverage, getting stuck, time to clean | Lidar or camera mapping, no-go zones |
| Dock | Hands-off emptying, mop washing | Bag cost, noise, footprint |
Airflow, sealing and the dust path
Suction only works if air is forced to travel through the path you intend. Gaps in the bin seal, a worn gasket or a loose filter let air leak in or out before it reaches the inlet, and the machine loses effective cleaning power regardless of motor strength. A well sealed dust path is a hidden quality feature, and it also decides whether fine dust is exhausted back into the room.
A clogged filter or a full bin raises resistance to airflow, so the machine cleans worse the longer you leave it. This is the same mechanism that drops the delivered airflow of an air purifier as its filter loads, covered in our CADR explainer. A robot vacuum that is never maintained will clean noticeably worse within weeks, even if its suction figure has not changed on paper.
Filtration matters for people with allergies. Many machines list a HEPA filter, but, as discussed in HEPA versus true HEPA, the label means little unless the dust path is sealed so air actually passes through it. A machine with a good filter and leaks around the bin is not filtering what it appears to. Look for a statement about sealing, and not only a filter grade.
Bin size and how often you empty it
Robot vacuums have small bins, commonly a few hundred millilitres. A larger bin means fewer interruptions in a big or hairy home. A small bin fills in one pass of a pet household, and the machine may return to its dock part way through a clean, or stop altogether if you do not empty it. Check the capacity in millilitres and how easy the bin is to empty without making a cloud of dust.
A bin that fills is not just inconvenient. As debris builds up, airflow drops and cleaning gets worse for the remainder of the run. If you have pets or long hair in the household, treat bin size and the auto-empty option as more important than a few thousand pascals of suction.
Check also how the bin handles fine dust. Some designs let dust escape when you open them, and some filters clog quickly with fine particles and need frequent washing. A washable filter that dries quickly and a spare filter in the box are practical points that decide how the machine copes after a few months.
Navigation: lidar, camera and bump
A robot that cleans every area methodically beats one with stronger suction that wanders. Navigation falls into three broad types. Bump and gyro systems move in patterns and turn when they hit something, so they cover a floor slowly and sometimes miss areas. Camera based systems use a camera to build a map and recognise objects, which can work well but may struggle in the dark. Lidar systems use a spinning laser to measure distances and build an accurate map, and they work in the dark.
Lidar and good camera systems let you set no-go zones, divide the home into rooms and clean particular rooms on command. They also tend to plan efficient rows rather than random coverage, so a clean takes less time and uses less battery. For a home with several rooms, mapping is a practical feature, more valuable than extra suction.
Obstacle avoidance is a separate matter. Cables, socks, pet waste and shoe laces are the usual causes of a stuck or tangled machine. Some models add cameras or sensors to avoid them, with varying success, and no source documents a standard test for it. Tidy the floor before a run regardless, and treat avoidance claims with caution until owner feedback confirms them. If the map is sent to an app, a stable network helps, as discussed in our mesh Wi-Fi guide.
Carpet versus hard floor
On hard floors, almost any robot picks up surface dust, crumbs and hair, and the differences come down to brush type, edge cleaning and how well fine dust in the cracks between boards is lifted. High suction can help with sand and fine grit between tiles. A rubber brush works well here and does not scatter debris as bristles sometimes do.
On carpet the differences are bigger. Low pile rugs are handled by most machines. Medium and deep pile require both agitation and airflow, and robots struggle with embedded dirt compared with an upright vacuum. A robot is a tool for daily maintenance, keeping dust down between proper vacuuming sessions, and not a full replacement for a deep clean on thick carpet.
Threshold climbing is another practical limit. Many robots cross a small step of about two centimetres, but a thick rug edge can stop them or fold the rug. Fringed rugs tangle brushes and can drag the machine. If you have rugs with long tassels or very thick pile, set no-go zones or lift them, and check the maker's stated maximum carpet height.
Mop add-ons
Many models add a water tank and a cloth for light mopping. These are best understood as damp wiping, which removes dust film and light marks, not scrubbing. A cloth dragged lightly across a floor will not lift dried stains, and models that vibrate or rotate their pads do better. A well designed system lifts the pad on carpet, which is an important feature, because a wet pad on a carpet is a disaster.
The combined machine is a compromise. The mop tank takes space that a bigger dust bin could use, and a model that does both well is usually the larger and costlier type with a dock that washes the pads. Check for carpet detection that lifts the mop, and for how the cloth is cleaned, since a dirty cloth just spreads grime.
Be careful with sealed wood and some finishes. Water on unsealed wood or laminate can cause swelling at the edges. Use the lowest water setting and check the floor maker's guidance. For a home that is mostly carpet, a mop feature is of little value and can be skipped.
Self-empty docks, bags and running costs
A self-emptying dock vacuums the bin into a larger bag or bin in the base, so you empty it every several weeks instead of every run. It is the biggest convenience upgrade after mapping, particularly for pet owners. The costs are a larger footprint, noise during emptying, and a recurring expense for bags, which are often proprietary and priced by the maker.
Check how the dock handles dust. Bagged docks keep dust sealed and are cleaner to dispose of, while bagless docks avoid the recurring cost but release more dust when emptied. Check availability and price of replacement bags and filters before buying, because a machine whose consumables are expensive or hard to find costs more over three years than its price suggests.
Also plan where the dock sits. It needs a clear space on both sides and in front, and should be near a socket and within good wireless range. A dock in a corridor can become a trip hazard, and a dock on a carpet may not be able to dock properly. Browse the home and kitchen category for related explainers.
Maintenance that keeps the cleaning level
A routine of a few minutes a week keeps a robot working. Empty the bin, clean or tap the filter, remove hair from the brush roll and side brush, wipe the sensors and the charging contacts, and check the wheels for debris. Neglecting the brush is the most common reason a machine appears to lose suction, when in fact the roll is jammed with hair.
Replace parts on schedule. Brushes, filters and side brushes wear, and the maker usually gives a guideline interval. A worn side brush stops sweeping edges and a clogged filter chokes airflow. Treat these as consumables and budget for them. Battery capacity also falls with age, and a machine that returns to its dock before finishing may need a new battery after a few years.
Safety and health considerations are modest but real. Robot vacuums can trip people in the dark, trap a pet's tail or paw, or pull a cable. Keep cables off the floor, and be cautious with small animals and toddlers. If a machine overheats, smells of burning or has a swollen battery, stop using it and contact the maker. Do not charge a damaged battery.
Noise is a last practical detail that specifications rarely state clearly. Higher suction modes run the motor harder and louder, and a machine that runs at its loudest setting while you work or watch television quickly gets switched to a quieter mode or banished to a schedule when nobody is home. If you intend to run it while at home, look for a quiet mode that still cleans acceptably, and check owner feedback about how the machine sounds on carpet and during bin emptying.
Scheduling and routines complete the picture. A machine that runs daily on a schedule keeps floors cleaner than a more powerful one run once a week, because dust never builds into a heavy load that overwhelms the bin. Running it when you are out also avoids the cord and toy obstacles that appear during the day. Consistency, more than raw power, is what makes a robot vacuum worth owning.
Frequently asked questions
Is higher suction always better for a robot vacuum?
No. Higher suction helps on carpet and with fine grit, but brush design, sealing, navigation and bin size matter as much. A figure in pascals cannot be compared between brands, so use it only as a rough guide within one maker's range.
How much suction do I need for pet hair?
Suction matters less than the brush and the bin. A tangle resistant rubber brush, a large bin and ideally a self-emptying dock handle pet hair far better than extra pascals. Expect to clean the brush regularly regardless.
Can a robot vacuum replace a normal vacuum?
For daily upkeep of hard floors and low pile carpet, largely yes. For deep cleaning thick carpet, stairs, upholstery and corners, you still need a conventional vacuum now and then. Most owners use both.
Is lidar better than a camera?
Lidar works in the dark and gives accurate maps. Camera systems can recognise objects and may avoid obstacles better, but depend on light. Both are better than simple bump navigation. Choose by owner feedback on how reliably each model avoids problems in homes like yours.
Do mopping robots really clean floors?
They remove dust film and light marks, which is useful for daily upkeep. They do not scrub dried stains. Models with spinning or vibrating pads and carpet lift perform better. For heavy soiling, a manual mop is still needed.
What does a self-empty dock cost to run?
The main expense is replacement bags, which vary in price and in how many empties each holds. Check the cost and availability before you buy. Some docks use no bags but release more dust when emptied.
The bottom line
Do not buy a robot vacuum on its suction figure. Treat pascals as a rough tier within one brand, and look instead at the brush design, the sealing of the dust path, the bin size, the navigation system and the cost of consumables. These decide how clean your floor stays.
For a home with pets, prioritise a tangle resistant brush, a large bin or a self-empty dock. For a multi-room home, prioritise lidar or good camera mapping with room control. For mostly hard floors, a rubber brush and good edge cleaning matter, and a mop add-on is optional.
Whichever you choose, tidy cables off the floor, empty the bin and clean the brush weekly, and replace consumables on time. A modest machine that runs often and is maintained beats a powerful one that is neglected.